Trade Box of 20
Sika Sikaflex Construction + Facade Concrete Masonry Joint Sealant in Concete Grey
Sika Code 438640
MPN FPSKFLEXCONCGY
Barcode 7612894961690
Sika Sikaflex Construction + Facade Concrete Masonry Joint Sealant Concrete Grey is a one part, moisture curing elastic joint sealant Trade Box of 20
Sikaflex Construction Plus is designed for connection joints in concrete Facade and masonry joints, in industrial floor and wall joints, joints between pre-cast concrete elements.
The all NewConstruction + sealant has double the flexibility with a massive +/- 35% movement accommodation necessary in building facade construction.
Sikaflex Construction plus need to be applied using a good quality 600ml barrel sealant gun.
Characteristics and Advantages
- Trade Discounted Box of 20
- Bubble-free curing
- Main use Joints in concrete facades
- Good application properties
- Good adhesion to most construction materials
- Very good resistance to weathering
- Solvent-free
- High movement capability
- Paintable
- Good workability
- Very low emissions
- Movement capability of ± 35
- Shelf life of 15 months
Backing Material:
Use closed cell polyethylene foam backer rod
Recommended for:
Concrete Facade joints
Non-porous Substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder-coated metals or glazed tiles have to be cleaned and pre-treated using Sika Aktivator 205
Porus Substrates Concrete, aerated concrete and cement-based renders, mortars and bricks.
Chemical Base:
i-Cure Technology polyurethane
Substrate Preraration:
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles.
Sikaflex Construction + adheres without primers and or activators, however, for optimum adhesion and critical, high performance applications, such as on multi-story buildings,
highly stressed joints, extreme weather exposure or water immersion, the following priming and or pretreatment procedures shall be followed:
Non-porous Substrates:
Aluminium, anodised aluminium, stainless steel, galvanised steel, powder-coated metals or glazed tiles have to be cleaned and pre-treated using Sika Aktivator 205 wiped on with a clean towel before sealing allow a flash-off time, other metals such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika Aktivator 205 wiped on with a clean towel, after the necessary flash-off time use a brush to apply Sika Primer 3N and allow a further flash-off time before sealing the joints, PVC has to be cleaned and pre-treated using Sika Primer 215 applied with a brush, before sealing allow a flash-off time.
Porous substrates:
Concrete, aerated concrete and cement-based renders, mortars and bricks shall be primed using Sika Primer 3N applied with a brush, before sealing allow a flash-off time.
For more detailed advice and instructions please contact the local Sika Technical Services Department.
Note: Primers are adhesion promoters they are neither a substitute for the correct cleaning of a surface nor do they improve the strength of the surface significantly.
Application Methods:
Sikaflex Construction+ is supplied ready to use over the top of the correct size Backer rod.
After the necessary substrate preparation insert a suitable backing rod to the required depth and apply any primer if necessary.
Insert a foil pack into the sealant gun and extrude Sikaflex Construction + into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment.
Sikaflex Construction Plus sealant must be firmly tooled against the joint sides to ensure adequate adhesion, it is recommended to use masking tape where exact joint lines or neat lines are required, remove the tape within the skin time.
Use a compatible tooling agent Sika Tooling Agent N to smooth the joint surfaces.
Do not use tooling products containing solvents.
If Sikaflex Construction + is dry-tooled it shows a slightly structured, concrete-like surface.
If it is wet tooled using a compatible tooling agent like Sika Tooling Agent N it shows a smooth surface.
Approvals and Standards
Resistance To Weathering ISO / DIS 19862
EN 15651-1 F EXT-INT CC 25 HM
ISO 11600 F 25 HM
ASTM C 920 class 35
Sika Construction+ Official Data sheets
Sika Sikaflex Construction + Technical Data Sheet
Sika Sikaflex Construction + Safety Data Sheet
Sika Sikaflex Construction Plus Manufacturer Page
Reviews
There are no reviews yet.